Power Amplifier

The circuit of traffic lights in my opinion is a series of easy-hard-easy to make.  Where we are required to be able to condition the flame of three lamps by following the existing traffic regulations. If we use computer programming as a regulator of the third condition of the lights probably we will not spend too much time to make it. As an example with microcontroller programming or programming-based computer applications such as Visual Basic, Delphi and many others. But if you use a common electronic circuit components used may be somewhat time consuming to get the results you are fully in accordance with the conditions of traffic lights that use the streets. Well ... if you're looking for examples of a series of simple traffic light above the range can I recommend to you. The working principle of a series of traffic light above is very easy to understand. The series of above use the output from IC up / down counter 74 190 as the producer output tercacah and then conditioned usi...

The series of emergency lights on this one is a series of emergency lighting is quite simple and not difficult to make.  Frankly this circuit is not my own design, but at least this series can add to your collection of electronic circuits. The circuit is actually almost the same as the battery charger circuit, it's just that in this emergency coupled switching circuit as a circuit breaker when the circuit load is connected to the supply voltage of 220 volts or in other words on the charging position. Meanwhile, when the voltage of 220 volts is lost (PLN lights off), then automatically switches the load switching circuit and turn on emergency lights, where the supply that is used is derived from batteries that have been installed in stand-by position. In a series of emergencies over the use of LED as a lighting load emergency. And indeed these days we find a lot of emergency lights that are sold in the market that use LEDs, but the LED is used instead led carelessly but has led a gl...

The series of light switches this time slightly different from the voltage of work. The series of light switches can work directly on the AC power network. Light switches are using the main component of TRIAC and LDR. The circuit is very simple and the components were sold in the market. If you want a light reception sensitivity of this circuit can be arranged then the 3.3 MOhm resistor can be replaced with a variable resistor. For more details can be seen from the following series of images. Circuit Diagram With Triac Light Switch series is prisipkerjanya as dimers, but dimers control performed by the reception of light around the LDR. The lower the intensity cayaha received LDR then semkin bright lights. For installation LDR need to be considered so as not exposed to light from the lamp directly.

Automatic Day-Night Lamp wit LDR Maybe it's a lot who know how to work this one series, but I wanted to share back to the beginner on this. In the existing lighting circuit automatic lights that use components LDR (Light Dependence Resistor). The workings of LDR LDR is exposed to light if the layer of the resistance was weakened likewise if there is no light at all resistance enlarged. here could make friends like that, because its components are a little easy but we will use the 220V AC voltage of course you must be very careful. Rather than actually being burnt. The author asks to be careful for the beginner course. Schematic LDR LDR components can be interconnected with a cable, so tools stay in the house but LDR is outside the home. It is recommended using qualified Relay no1 to avoid fire, because the relays are cheap to produce heat. Relay that cheap is not in use for high voltage. Travonya use the cheap, because this circuit does not require large currents. The function of P...

Emergency Lamp With 555 is one solution for lighting during power outages. With Emergency Lamp Series 555 uses a 12VDC voltage source that can be supplied from the 12V battery. Emergency Lamp 555 Series With these very simple and easy to make because all the components easily available in the market. Emergency Lamp Series With this 555 can turn on the light 5W-10W. The circuit is built with an astable multivibrator with the IC 555 that is used to mendrive transformer through Q1. For more details can be viewed directly from the series Emergency Lamp With 555 follows. Emergency Lamp Using TLC555 Working frequency range of 555 Emergency Lamp With this set of configurations R1, R2 and C2. T1 in series Emergency Lamp With 10V 500mA 555 is a transformer. Secondary part (0-10V) is connected to the Q1 to be given the signal from the multivibrator. Then the primary (0-220V) is connected to the lamp.

This led series will Blinking alternately, The way it works is determined by IC NE555 and transistors are used as reinforcement for each section (20 upper, 20 lower) work optimally. 555 circuit below is a flashing bicycle light powered with four C, D or AA cells (6 volts).  Two sets of 20 LEDs will flash alternately at about 4.7 cycles per second using RC values ​​shown (4.7K for R1, 150K for R2 and 1uF capacitor). Time intervals for two lights about 107 milliseconds (T1, LED on) and 104 milliseconds (T2 lower LEDs).  Two transistors are used to provide additional time beyond the current limit of 200mA from the NE555 timer. A single LED is placed in series with the PNP transistor base so that the 20 LED 555 is turned off when the output is high during a time interval T1. High-level output timer 555 is 1.7 volts less than the supply voltage. Adding the LED forward voltage increase is required for the PNP transistor to about 2.7 volts, so the 1.7 volt difference from the supply ...