Power Amplifier

USB connector there are only 2 kinds, namely the connector type A and type B connector, as shown below. Type A connector used to connect the USB cable into the USB terminal on the back of the computer the last few years of production. Type B connector used to connect the USB cable into the USB terminal on the equipment, for a simple USB devices, such as mouse, usually do not use the connector B, to save cost in the cable directly connected to the inside of the mouse. Specified in the standard reference pesyaratan very strict to USB cable, not just the cable can be used, all the more for USB full-speed transfer of data to 1.2 Mega bps. So that the USB cable always sold as a ready-made, one end attached to the connector type A and the other end attached to the connector type B, no one sells it off the USB connector. On the computer, usually there are two terminals for connector type A, so it can easily be paired with 2 pieces of USB devices. Manufacturing company that makes the ...

Easily connected to the computer because it does not need to open the computer cover. Uniform shape USB connector, there are only two forms of type socket. Hot-plugable - that USB devices can be connected when the computer is on Plug and Play - USB equipment that is easy to use, when connected to a computer, the computer will recognize the pick up program (driver) in accordance with the equipment. Equipment that requires little resources, can take resources from the USB port. Resources off equipment when not in use. High-speed data transfer, can reach 12Mbps. One USB port can be connected with 127 tools. USB Cable   Has a fault monitoring and data transmission will be repeated to ensure reliability of data.

USB cable consists of 4 wires plus a conductor wire wrapping, such as the protectors are usually found in the audio cable. Cable number 1 is used to channel resources to the voltage of 5 volts, if necessary USB devices may draw power from this line and should not exceed 100 mA. Computer equipped with USB capability, is required to provide power at 100 mA for this purpose. USB devices that require more power than the aforementioned provisions, must provide their own resources for the purposes work equipment. The USB cable signals Number 4 is the ground cable as a back channel source voltage of 5 volts. Cable number 2 and number 3 is used for signal transmission. No. 2 cable and cable called D-3 numbers called D, the voltage on the two channels is changed between 0 Volt and 3.3 Volt. Digital signal is sent through the two channels are said to be 'difference signal', which means that the signal digital '0 'or '1' is not declared to the magnitude of the voltage on ...

Create USB PowerInjector for GSM Modem Maximizing and stabilization USB voltage . Sometimes we need also to extend the USB cable connection. Usually cable so the store is no more or less than one meter. If the cable is good quality automatic reduction of voltage and current remain so flash media or a modem to function remained normal. Sometimes the two media are not readable because of a decline in flow due to cable resistance is very large, so that lost power wasted. USB injector circuit If this happens often flash or USB modem off often error-disconnected. To overcome this decrease in voltage performance. The principle is quite very simple. You simply "inject" is indeed voltage VCC 5VDC needed a modem or a flash. Finishing USB inject After using the USB power injector is expected regardless of the length of external cable fixed voltage maximum. The principle works is simple enough original 5VDC voltage of the CPU / your computer off and then injected...

Creating a sound card is not more complex problems. If you use Great IC PCM2702 from Burr RED / Texas Instruments you can create a card USB sound fully functional. The sound card can be activated from the USB port and has one stereo output. You do not need to install drivers for Windows XP and Vista, because the driver is already in the system, XP and Vista. So this series is really plug and play. Block Diagram Description The core of this construction is a 16-Bit Stereo Digital-To-Analog Converter with PCM2702 USB interface. Schematic diagram USB soundcard PCM2702 only requires a few additional components to work. This scheme is not complex. The sound card can be activated directly from the USB port (jumper W1) or from an external power supply (jumper W3). PCM2702 requires two 3.3V power supply (3V-3.6V) and 5V (4.5V-5.5V). I use a fixed output voltage to 3.3V LDO TPS76733Q (IO2) and the output voltage is adjusted to 5V LDO TPS76701Q (IO3). LDO Both are produce...

USB Battery Charger For Lithium Ion battery with the LM3622 is a series of lithium ion battery charger. This charger circuit operates using power from the USB source PC. Current consumption of a series of USB Battery Charger For Lithium Ion battery with 400mA LM3622 is limited by R1, so it does not exceed the current maximum limit that can be given by a USB computer. Brains from USB Battery Charger For Lithium Ion battery with IC LM3622 , it is a national of having special technical specification charger for lithium ion batteries. In a series of USB Battery Charger For Lithium Ion with LM3622 R1 0.25 Ohm value that serves to limit the charging current 400mA to the battery. Q2 and Q1 is the last part of the USB Battery Charger For Lithium Ion battery with the LM3622. In principle, USB Battery Charger For Lithium Ion with LM3622 identify the condition of the battery full charged battery voltage via pin 6 LM3622. USB Series Lithium Ion Battery Charger For LM3622 is equipped with a switch ...

Here's a simple VHF FM transmitter that could be used to play audio files from an MP3 player or computer on a standard VHF FM radio. The circuit use no coils that have to be wound. This FM transmitter can be used to listen to your own music throughout your home. When this FM transmitter used in the car, there is no need for a separate input to the car stereo to play back the music files from your MP3 player. To keep the circuit simple as well as compact, it was decided to use a chip made by Maxim Integrated Products, the MAX2606 [1]. This IC from the MAX2605-MAX2609 series has been specifically designed for low-noise RF applications with a fixed frequency. The VCO (Voltage Controlled Oscillator) in this IC uses a Colpitts oscillator circuit. The variable-capacitance (varicap) diode and feedback capacitors for the tuning have also been integrated on this chip, so that you only need an external inductor to fix the central oscillator frequency. USB FM transmitter schematics It is poss...

Cellphone battery charging process when we're done traveling is a big problem. Because when traveling source of power supply is generally difficult to find. If you turn on your phone then the battery continuously over time will run out within a period of five to six hours and eventually mobile phones unusable. Here is described a series of simple charger that will increase battery life two to three hours. In principle, the charger uses a series of Limited Voltage Current Source. Generally requires cellphone battery voltage 3.6 - 6 volts DC and currents 180-200 mA to perform the charging process. Cellphone battery usually consists of three NiCd battery cells, and each cell has a voltage of 1.2 volts potential. At the speed - average low flows required to charge mobile phone battery about - about 100mA. In this series there is a 12V voltage source consists of 8 regular battery cells (each cell 1.5 Volt) able to supply current at 1.8 A which is connected with output terminals. The cir...

This really a work that so cool if you like modif PC. So this is a USB interface for alphanumeric LCD display like 4 × 20 which can be controlled with LCD Smartie program. USB interface is implemented by using PIC18F2550 microcontroller, Using USB LCD modules. Below is a project of the USB LCD controller. Schematic circuit and PCB design source  | link

Usb series player is an electronic device or electronic circuit that functions as an MP3 player that is stored on a storage device such as USB flash. In this usb circuit using an IC as a modifier of digital voice data into analog so that it can be applied to a headphone, or again through the power amlplifier strengthened so that it can be heard through the speakers. IC used in this circuit using IC PCM2902 as a modifier of a digital data into analog data storage. Below is a schematic diagram of a USB player. Schematic usb player