12 Volt Battery charger , and also can Accu Charger

By -
This 12 Volt Battery charger circuit best performance to charger 12 volt battery . Why this charger is best performance because this 12 Volt Battery charger quickly to recharger battery and shuts off at full charge. Initially , charging current is limited 2 A , but you can change for the transistor. As the battery voltage rises , current  to the battery decreases , and when the current has decreases to 150 mA or 0.15 A  this 12 Volt Battery charger switches  to a lower float voltage , which prevents overcharge.

See this 12 volt battery charger schematic below :



12 Volt Battery charger
12 Volt Battery charger Click to view Enlarge
The 12 Volt Battery charger can be charger wet  accu and dry accu , and to be make the accu old last longer. The output charger goes to 14.5 Volt. As the battery or accu approaches full charge , the charging current decreases and the output voltage is reduced from 14.5 Volt to about 12.5 volt, terminating the charging.

Comments

  1. UnknownApril 26, 2013 at 6:53:00 PM GMT+7

    Another factor that is important in sizing the 12 volt car battery performance is the CCA ( cold cranking amps )
    ratings that measures the amps if they exceed or meet the at 0 degrees F and can sustain for 30 seconds
    while having a voltage higher than 7.2 depending on the condition of the climate of the place.

    ReplyDelete
  2. ChrisJanuary 30, 2014 at 10:42:00 PM GMT+7

    Hi,
    Thank you for sharing this knowledge. Can you please help me with an information? I need a 12 volt battery charger with 12-14 amps capacity. from the schematic above, what are the components I need to change to achieve this? and what exact specs of the components?

    Many Thanks.

    Chris

    ReplyDelete

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more