Create a Digital Volume Control Circuit

By -
This series is the volume of the digital amplifier That is used on or tone control. This series ic type using DS1669 Digital Pot IC specifically for this volume match. a series of settings used at the middle-class amplifier That small powerless under 50 watts.volum11components: C1 = 0.1uf Ceramic, IC = IC DS1669 Digital Pot, S1 / S2 = digital swicthOr you can use the series to this one:volum2The Work: The digital volume control IC uses 9.
Click to view larger.


Required to operate the series voltage regulator is 12 volts. IC1 (555) is very good to work as a flip-flop. Frequency or period can be determined with selecting value of resistor R44, R45 is combined with a capacitor C6. In this series has a 0.3 second period.IC2 is used to Decrease or increase of the calculation. In the series of this mode is used to raise up and down mode is used to Decrease the volume. 
While IC4 and IC3 has a 16-channel, analogue multiplexers, while working as an analog switch. IC3 is used as in the series of level indicator while IC4 is used as potentiometer.After the next power in the on-it, and the switch S1 is pressed to reset. When the switch S2 is pressed, the IC2 and the balance in the form of output legs responded B, C, and D in CMOS IC2. Output B, C and D control line inputs IC2 and IC3, and the chosen one, the 16-channel output, by turning on the analogue.In this series, IC4 is used as the potentiometer is connected to the That resistor 15 (R9 to R23) each of the 16 input pins and resistor / capacitor combination with C2, C3 and R7 to the output. 
Switch S2 is used to raise and switch S3 is used to Decrease the volume.Electrolyte capacitor of 1uF (C4) is used to Prevent the occurrence of noise. While the R8 and the resistor R6 is used to Prevent Tension on the half-supply voltage in order to avoid distortion of the audio signal coming from the preamplifier. Meanwhile, capacitor C2, C3 and resistor R7 is provided to filter the audio. Happy work, hopefully successfully. 

 COMPONENT LIST:

R1, 2, 3, 4: 560R R16: 1,5KR45: 150KR5: 680RR17: 3,3KC1: 0,01uFR6, 8: 100KR18: 5,6KC2, 3: 100nFR7: 1MR19: 8,2KC4: 1uF/50VR9: 10RR20: 15KC5: 100nFR10: 12RR21: 33KIC1: 555R11: 42RR22: 56KIC2: 74193R12: 100RR23: 1,5MIC3: CD4067R13: 220RR24…R39: 560RIC4: CD4067R14: 470RR40..R43: 4,7KIC5: 7805R15: 820RR44: 330KIC6 N1-N4): 7407

Comments

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more