TA8210AH Stereo Car Power Amplifier

By -
IC TA8210AH By using this you can apply a series of audio power amplifier is the car audio system. In general, all the speakers in the car using a subwoofer speaker, and woofer. Because the car is not big room so the sound is being required is not too high.

Audio amplifier circuit can work at a minimum voltage 12-volt DC, if supplied under voltage 12-volt amplifier work will be less than the maximum. This amplifier output power up to 200W or 2 x 100W stereo with 8 ohm impedance.



200W car amplifier schematic

Part List :

Resistor

R1 =1K

R2 =50K trim

R3 =1K

R4 =50K trim

R5 =680R

R6 =680R

R7 =150K

R8 =2R2

R9 =2R2

R10=2R2

R11=2R2



Capacitor

C1 =1uF

C2 =1uF

C3 =47uF

C4 =47uF

C5 =100n/400V

C6 =220uF

C7 =220uF

C8 =100n/400V

C9 =100n/400V

C10=100n/400V



Intregated Circuit

IC1=TA8210AH



Connector

X2-3=in R

X2-2=gnd

X2-1=in L

X1-1,X1-2=Out R

X1-3,X1-4=Out L

Comments

  1. akhilJuly 8, 2012 at 12:02:00 AM GMT+7

    y r8=2r2?

    ReplyDelete
    Replies
    1. UnknownFebruary 6, 2013 at 11:36:00 PM GMT+7

      it's 2.2ohms !! you will see 2k2 Ohms and 2M2 Ohms. They mean 2,200 Ohms and 2,200,000 Ohms, this system reduces the chances of missing the decimal point --- in circuit design and construction, it is a disaster to use a resistor that is 67 Ohms when a 6.7 Ohm resistor is needed.

      Delete
  2. Share Tech EverythingMarch 15, 2013 at 7:00:00 PM GMT+7

    have you try this circuit ?
    does it really a 200watts amplifier?

    ReplyDelete
  3. UnknownOctober 17, 2013 at 11:28:00 PM GMT+7

    Pout (1) = 22W / Channel (Vcc = 14,4V, f=1kHz, THD = 10%, Rl = 4 Ohm)
    Pout (2) =19W / Channel (Vcc = 13,2V , f=1kHz, THD = 10%, Rl = 4 Ohm)

    ReplyDelete
  4. UnknownSeptember 16, 2015 at 10:43:00 PM GMT+7

    I made this and use it few times.
    real wattage is 18W per channel

    ReplyDelete
  5. Electronic CircuitMarch 25, 2016 at 4:32:00 PM GMT+7

    yes its real wattage but the circuit upgrade its

    ReplyDelete

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped ...
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more