Troubleshooting STR IC Regulator Power Supply

By -

A. Unable to start.
Can be caused by:
  • No start-up voltage supply Vcc or a voltage less than 16V
  • Electrolityc Capacitors supply voltage Vcc filter dry.

  
2. Led indicator blinking
If the supply voltage Vcc examined rocking. This is because the regulator of life and death because OVLO work., Die-protectionist regulators and auto start life over and over. If it is turned off Electrolityc Capacitors  usually still keep the rest of the cargo.
Can be caused by:

  • Electrolityc Capacitors supply voltage Vcc filter on a pin-4 dry. Replace with a value equal to or slightly larger. - triger UVLO
  • input filter capacitor on pin-1 feed dry behind the declining value - triger OLP
  • Rectifier diode of the switching transformer is damaged (sometimes when examined with avo-meter looks like a still good)
  • cause the supply voltage Vcc drops of the switching transformer (UVLO)
  • Part damage or broken lines on the feedback circuit of the voltage regulator through B to photocoupler - triger OVP
  • Electrolityc Capacitors dry filter voltage B - triger OVP
  • One of the output voltage of the switching transformer secondaries there is a short (over load) - triger OLP
  • Soft start capacitor value decreases - triger OLP

3. Noise arising (noise)
Can be caused by:

  • Transformer windings slack.
  • If there are ceramic capacitors - can sometimes cause interference noise due to its characteristic piezoelectrik like crystal resonator. Replace with film capacitors.

4. When the st-by normal stress. But when the power is on the regulator directly off protectionism no voltage on the secondary this part. Electrolityc Capacitors  are still storing charge.
Can be caused by:

  • Sensor OVP small value resistor on pin-2 to the ground so that the value of delayed triger to OLP or OCP.
  • Regulator IC is damaged

---------------------------------------------------------------------------------------------------------------------------
Note: Be careful when the regulator is not working. Because of Electrolityc Capacitors  may still have a charge when turned off.

Comments

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more