Parts of the UPS (Uninterruptible Power Supply)

By -

Uninterruptible Power Supply
UPS is basically composed of three main components, namely:
1) Rectifier-Charger
This section is used to transfer circuit and battery charging. Rectifier-charger circuit block is going to supply the power needed by the inverter under full load and at that time to maintain the charge in the battery. Besides these blocks must have the ability to drain the power output of 125-130%.

Characteristics of the batteries also need to be taken into account in its charger circuit design because if a rechargeable battery with a current that exceeds the capacity limit will be able to shorten the life of the battery. Usually for a battery charging current to the UPS is 80% of current conditions issued by the batteries at full load.
Limitation of a UPS system is good by the standards of NEMA - National
Electical Manufacturer Association - is able to provide 100% power continuously (continuous load) and 2 hours at 125% load without a decrease in performance (damage). The battery can still be categorized as unfit for use if the condition is still capable of providing 100% power for 1 hour if the time of filling for 8 hours (determined by the manufacturing
battery).

The quality of the inverter is a determinant of the quality of power generated by a UPS system. Inverter function to change the DC voltage of the rectifier-charger circuit into AC voltage signal in the form of a sine wave formation and after going through the filter circuit. The resulting output voltage must be stable both voltage amplitude and frequency, low distortion, there are no voltage transients.
In addition, the inverter system needs a feedback circuit (feedback) and the regulator circuit to maintain constant voltage to be obtained.

3) Switch Shifters (Transfer switches)
Transfer switch is divided into two types, namely electromechanical and static. Electromechanical switch uses relays to get one of the supply voltage terminal and the other from the UPS system. Static switch system using semiconductor components, such as SCR.
The use of SCR would be better because of the removal operation is performed with the SCR takes only 3 to 4 ms, while the electromechanical switch is about 50 to 100 ms.
The use of UPS is done by connecting the UPS to the AC input and output PLN UPS to the load. Most UPS are used to supply the computer, because if the source of PLN suddenly dies, then the data being processed is not lost but is still in the back-up by UPS, so there's still time to save data.

Comments

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more