12V to +/- 20V DC Converter Circuit

By -
100 Watt 12V to +/- 20V DC Converter Circuit
DC To DC Converter circuit used to be an convert  voltage DC to DC with different concepts. DC to DC converter circuit +12 V to + /-20V is working to change the battery voltage from 12V DC to 20V DC voltage symmetrical. DC to DC converter circuit is often applied to the power amplifier udio on car audio systems. DC to DC converter circuit uses a TL494 IC as power plsa for the converter. 
TL494 IC is a PWM controller with an adjustable frequency from 40-60Hz through a potentiometer. Then from the TL494 PWM signal is given to the driver MOSFET inverter TPS2811P to be given to the power inverter with 2 units of MOSFET transistors. Circuit details can be seen in the figure following the DC to DC converter.

DC To DC converter circuit +12 V To + / - 20V 

Click to View Larger

List Components DC To DC Converter +12 V To + / - 20V
  • R1, R2 = 10 
  • R3, R4, R6, R7 = 1k 
  • R5 = 22k 
  • R8 = 4.7k 
  • R9 = 100k 
  • C1, C2 = 10000uF 
  • C3, C6 = 47 u 
  • C4 = 10U 
  • C5, C7, C14 = 100n 
  • C8, C9 = 4700u 
  • C12 = 1N 
  • C13 = 2.2u 
  • U1 = TL494 
  • U2 = TPS2811P 
  • Q1, Q2 = FDB045AN 
  • D1-D4 = 1N5822 
  • D5 = 1N4148 
  • FU1 = 10A 
  • L1 = 10U 
  • L2 = ferrite BEAD 
  • RV1 = 2.2k 
  • RV2 = 24k 
  • T1 = TRAN-3P3S 

DC To DC converter circuit +12 V To + / - 20V is capable of supplying up to 100W and can power supplying currents up to 3A. In making DC To DC Converter +12 V To + / - 20V has to be careful and cautious because there are parts of DC To DC Converter +12 V To + / - 20V in the form of an AC circuit.

Comments

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more