Line Follower Robot with AVR ATMega8535

By -
Line Follower Robot with AVR ATMega8535 - Make the robot line follower is exciting, especially for those who like to friends experimented with AVR microcontroller ATMega. "Line Follower Robot" is a robot designed to follow the trail (can be a line putus2 line or even a point to point). Creating a Line Follower Robot uses an AVR microcontroller ATMega 8535 is very possible and very reliable. Due to the design of a Line Follower Robot should we think that the trail will be followed step by step Line Follower Robot will be made to track or path in Line Follower Robot is passed. And of the Line Follower Robot needs tersbut feature2 owned by AVR microcontroller ATMega 8535 is sufficient and meets the needs of the Line Follower Robot. Line Follower Robot in the article with AVR ATMega8535 I made a simple graffiti to be possessed by a Line Follower Robot.

Line Follower Robot Block Diagram of the AVR ATMega8535

Block Diagram of Line Follower Robot with AVR ATMega 8535
Block Diagram of Line Follower Robot with AVR ATMega 8535


Function Block Diagram of Line Follower Robot with AVR ATMega 8535 :
  1. Line Follower Robot Sensor on can use a photo diode or photo transistor, this section serves to detect the presence of trajectory track.
  2. Keypad, this part of the function buttons to start / stop Line Follower Robot and as voters Line Follower Robot configuration settings for the field will be going through.
  3. Display, a part which serves to show the option of setting and the setting (it is enough that needs to be in view) of this section or the viewer can use a 7 segment LCD.
  4. Motor Driver, this part of a series of H Bridge DC motor driver. This section controls the motor in langsun. This section is an AVR microcontroller interface anatara ATMega with DC motor. I like to use the IC motor driver L298 family.
  5. ATMega8535 AVR microcontrollers, this section is the part that determines where the robot will be taken based on the data from the sensor. This section is set langkah2 Line Follower Robot in the conquest of the track.
×××× Creating a Line Follower Robot  ××××

Comments

Post a Comment

Popular posts from this blog

1500W Stereo Power Amplifier Schematic

By -
Image
Circuit Power Amplifier has a power output of up to 1500W RMS power amplifier circuit is often used to power sound systems keperlun for outdor. In the final image can be seen a series of power amplifiers using 10 sets of power transistors for the ending. This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. The series of High Power Amplifier 1500W With Transistor Click Image to view larger In the above series of power amplifer 1500W is equipped
Read more

TDA2030 complete tone control

By -
Image
At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.
Read more